TANDBERG DATA TDC 3620, TDC 3640, TDC 3660 (VER. 2) Device Type Tape Drive Interface SCSI-2 Format QIC-24 (TDC3620), QIC-120 (TDC3640), QIC-150 (TDC3660 VER. 2) Sustained Transfer Rate Unidentified Size 5.25 in. half height View Top CONNECTIONS Function Label Ground connector CN1 Note: CN1 not present on all models. USER CONFIGURABLE SETTINGS Setting Label Position » Factory configured - do not JP1/Pins 1 & Unidentified alter. (Serial communication 2 out) » Factory configured - do not JP1/Pins 3 & Unidentified alter. (Serial communication 4 in) Parity check enabled JP1/Pins 5 & Closed 6 Parity check disabled JP1/Pins 5 & Open 6 DRIVE SELECT ID Drive ID JP1/Pins 7 & 8 JP1/Pins 9 & 10 JP1/Pins 11 & 12 » 0 Open Open Open 1 Open Open Closed 2 Open Closed Open 3 Open Closed Closed 4 Closed Open Open 5 Closed Open Closed 6 Closed Closed Open 7 Closed Closed Closed Note: Pins 2 & 4 of JP1 must be open to enable SCSI ID select. With Pins 2 & 4 of JP1 closed, factory test functions are enabled via pins 7-12. MANUFACTURERS RECOMMENED MEDIA Drive Tape Capacity Without Capacity With Compression Compression TDC 3620 3M® DC300XL 45MB Unidentified 137m TDC 3620 3M® DC300XLP 45MB Unidentified 137m TDC 3620 DEI 169m 55MB Unidentified TDC 3620 DEI Ser. II 55MB Unidentified Gold Plus 169m TDC 3620 3M® DC600A 183m 60MB Unidentified TDC 3620 3M® DC600XTD 60MB Unidentified 183m TDC 3640 3M® DC600A 183m 125MB Unidentified TDC 3640 3M® DC600XTD 125MB Unidentified 183m TDC 3660 3M® DC600A 183m 125MB Unidentified (VER. 2) TDC 3660 3M® DC600XTD 125MB Unidentified (VER. 2) 183m TERMINATING RESISTOR CONFIGURATION Function RP1 RP2 RP3 Termination Terminator Terminator Terminator enabled installed installed installed Termination Terminator not Terminator not Terminator not disabled installed installed installed DIAGNOSTIC LED(S) LED1 (Red) Condition Fatal Blink-Code* Error Short Short Short Short Short Short No error Short Short Short Short Short Long Append error Short Short Short Short Long Short Bad command block Short Short Short Short Long Long Bad parameter block Short Short Short Long Short Short Bus parity error Short Short Short Long Short Long Busy Short Short Short Long Long Short Capst. servo B error Short Short Short Long Long Long Cartridge removed Short Short Long Short Short Short Compare error Short Short Long Short Short Long Copy data error Short Short Long Short Long Short Copy managem. error Short Short Long Short Long Long File mark error Short Short Long Long Short Short Head servo B error Short Short Long Long Short Long Illegal command Short Short Long Long Long Short Illeagal copy Short Short Long Long Long Long Illegal length Short Long Short Short Short Short Inappropriate request Short Long Short Short Short Long Latch error A Short Long Short Short Long Short No cartridge Short Long Short Short Long Long Not loaded Short Long Short Long Short Short Power-on request Short Long Short Long Short Long QIC. No data detected Short Long Short Long Long Short Read after write error Short Long Short Long Long Long Read EOM logical Short Long Long Short Short Short Read EOM physical Short Long Long Short Short Long Reserv. Conflict Short Long Long Short Long Short Sensor error B Short Long Long Short Long Long Tape runnout B Short Long Long Long Short Short Unit attention Short Long Long Long Short Long Write EOM warning Short Long Long Long Long Short Write EOM Short Long Long Long Long Long Cartridge write prot. Long Short Short Short Short Short 16 rewrite errors Long Short Short Short Short Long 24 rereads. Blk. fnd. Long Short Short Short Long Short 24 rereads. Not fnd. Long Short Short Short Long Long Illegal copy function Long Short Short Long Short Short Illegal header Long Short Short Long Short Long No header Long Short Short Long Long Short Too large address Long Short Short Long Long Long Bad ID or LUN Long Short Long Short Short Short Partial Description Long Short Long Short Short Long Bad target status Long Short Long Short Long Short Check condition Long Short Long Short Long Long Data transfer error Long Short Long Long Short Short Selection failure DIAGNOSTIC LED(S) CONTINUED LED1 (Red) Condition Fatal Blink-Code* Error Long Short Long Long Short Long Sequence error Long Short Long Long Long Short Illegal block size Long Long Short Short Short Long Buffer size A error Long Long Short Short Long Short Rereads outside limits Long Long Short Short Long Long Rewrites outside limits Long Long Short Long Short Short Buffer error. A Low nibble Long Long Short Long Short Long Buffer error. A High nibble Long Long Short Long Long Short Unspec. fatal error Long Long Short Long Long Long Timeout error B Long Long Long Short Short Short Buffer RAM A error Long Long Long Short Short Long Drive contr. A Error Long Long Long Short Long Short EEPROM A verification Long Long Long Short Long Long EEPROM error A Long Long Long Long Short Short External RAM A error Long Long Long Long Short Long SCSI contr. A Error Long Long Long Long Long Short Spurious B interrupt Long Long Long Long Long Long Stack B overflow Note: Type ‘A’ Code: Error cannot be reset. Drive will continue to report error with a blinking code once initial error has occurred. Service is required. Type ‘B’ Code: Errors are failures in the Drive or the cartridge. Error can be cleared by RESET and information saved in EEPROM. .